ELITECH PM 1218
Short review
Buy ELITECH PM 1218
Characteristics of ELITECH PM 1218
Yandex.Market data
| General characteristics | |
| A type | detachable |
| Design | tabletop |
| Power | 1200 watts |
| Number of speeds | 1 |
| Working with metal | there is |
| Treatment | |
| Cutting height | 50 mm |
| Disc diameter | 180 mm |
| Bore diameter | 22 mm |
| Tilt angle | 45 deg. |
| Performance | |
| Rotational speed | 5000 rpm |
| Additional Information | |
| Weight | 5 Kg |
| Food | |
| Network cable length | 2.6 m |
Reviews about ELITECH PM 1218
Yandex.Market data
Advantages:
Three times lighter than a 355 mm saw, easy to carry, inexpensive. Engine power is sufficient. The build quality is average (there were worse models). It is more convenient to work than a stand for angle grinders.
Disadvantages:
There are slight backlash in the design. Could have made a larger disc: 200-230 mm.
Comment:
I was taken to a workshop in a dacha for cutting profiled pipes of a small section. I did not use the disk from the complete set, I immediately put the reinforced "Luga". It is much more convenient and faster than a grinder, it cuts smoothly. Complements the grinder: the grinder constantly has a grinding disc, it is unnecessary to constantly change discs. Cuts pipes up to 40x40mm in one step. 50x50 mm and 60x60 mm are cut in several steps, you have to turn them over. Standard discs from a 180 mm grinder with a 22.2 mm hole are suitable. Includes spare brushes for the engine and an additional adapter for cutting discs with a 25mm hole. The guide for setting the angle of the cut, I had a curve, removed and straightened with a hammer.
May 5, 2016, Nizhny Novgorod
Advantages:
In the weight category of the product, it is determined .. Compactness. I managed to put not only a new cut-off, but also a grinding wheel, pleased, compensates for the absence of a sharpening groan ..)
Disadvantages:
The main thing, as it seemed to me, was that when cutting a corner, I personally needed to cut it off, measuring 35mm in width .. I found out that if it were 40mm, for example, then I wouldn't be able to do this, at an angle of 45`
Comment:
I advise, in the garage and not only a non-replaceable thing Included with the welding investor, if any ..
11 February 2020, Moscow
Advantages:
Inexpensive
Disadvantages:
At 45 degrees, the 40/40 profile does not fit into a vice, the flimsy frame, the disc in the kit is outright rubbish! Change immediately! 180 disc, but for this price, that's ok
Comment:
For such a price for home, non-professional use will go
November 21, 2019, Volgograd
Advantages:
Everything is neat and on time!
Disadvantages:
not yet
Comment:
I think I will have impressions when I work!
December 19, 2019, Murmansk
Advantages:
Price, simplicity, compactness
Comment:
Works, cuts until it breaks
January 27, 2017, Moscow
Advantages:
the price, in principle, is what I need, a larger instrument will be redundant.
Disadvantages:
there is no smooth start, it starts too abruptly, the landing spindle where the disc is worn a little less than the dry-barn one, which is why the Bulgarian discs beat, I cut out a strip from a thin plastic bottle, it just enters with an additional seal, along the entire diameter of the spindle, the bottle is needed straight thin from cheap soda, fat ones don't fit
Comment:
He doubted for a long time whether to take it or not. But I made up my mind, it is of course small, large diameters cannot be cut, but I rarely have such a need. It's better not to press hard on it, and I changed the disc right away. For that now the saws are even, there were problems with this)) I connect through a homemade soft start, the power of course falls from this, but not critical. In general, for its 3800 I think the adapter for the grinder is more successful than for the same money. AND + the ability to use two tools at once
May 15, 2019, Moscow
Advantages:
The price is consistent with the product. For domestic use, the very thing!
Disadvantages:
Inconvenient power button. Flimsy table with a clamp. The disc requires perpendicular adjustment to the guests. There is something to work on !!!
Comment:
March 31, 2020, Saratov
